ASTM A694/A694M Standard Specification for Carbon and Alloy Steel Forgings for Pipe Flanges, Fittings, Valves, and Parts for High-Pressure Transmission Service
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- SNV SN EN 13611+A2 Safety and control devices for gas burners and gas burning appliances - General requirements
- 23
- SNV SN EN 12561-4 Railway applications - Tank wagons - Part 4: Devices for top filling and emptying of liquid products
- CEN EN 12561-2 Railway applications - Tank wagons - Part 2: Bottom emptying devices for liquid products including vapour return
- CEN EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
- BSI BS EN 12561-2 Railway applications - Tank wagons Part 2: Bottom emptying devices for liquid products including vapour return - CORR: August 31, 2011
- CEN EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
- CEN EN 12561-2 Railway applications - Tank wagons - Part 2: Bottom emptying devices for liquid products including vapour return
- CEN EN 12561-2 Railway applications - Tank wagons - Part 2: Bottom emptying devices for liquid products including vapour return
- CEN EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
- BSI BS EN 12561-2 Railway applications - Tank wagons Part 2: Bottom emptying devices for liquid products including vapour return - CORR: August 31, 2011
- CEN EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
- BSI BS EN 12561-2 Railway applications - Tank wagons Part 2: Bottom emptying devices for liquid products including vapour return - CORR: August 31, 2011
- ISO 4200 Plain End Steel Tubes, Welded and Seamless - General Tables of Dimensions and Masses per Unit Length - Fourth Edition; Replaces ISO 134: 1973 and ISO 336: 1976
- ISO 21049 Pumps Shaft sealing systems for centrifugal and rotary pumps - First Edition
- ASME B16.11 Forged Fittings, Socket-Welding and Threaded
- Картотека зарубежных и международных стандартов
ASTM International
Standard Specification for Carbon and Alloy Steel Forgings for Pipe Flanges, Fittings, Valves, and Parts for High-Pressure Transmission Service
N A694/A694M
Annotation
This specification covers forged or rolled steel pipe flanges, forged fittings, valves, and parts suitable for use with high-strength transmission-service pipe. Included are flanges, fittings, and similar parts ordered either to dimensions specified by the purchaser or to ASME or MSS dimensional standards referenced in Section 2.
Several grades of material, based on minimum yield strength requirements, are covered, as indicated in Table 1.
Supplementary Requirements are provided. Supplementary Requirement S1 is provided for use when purchaser approval is required for repair welding.
This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.
The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
*A Summary of Changes section appears at the end of this standard
Автоматический перевод:
Стандартная спецификация для штамповок углеродистой и легированной стали для фланцев трубы, деталей, клапанов и частей для обслуживания передачи с высоким давлением
