ASTM A182/A182M REV A Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- SNV SN EN 13611+A2 Safety and control devices for gas burners and gas burning appliances - General requirements
- 23
- SNV SN EN 12561-4 Railway applications - Tank wagons - Part 4: Devices for top filling and emptying of liquid products
- CEN EN 12561-2 Railway applications - Tank wagons - Part 2: Bottom emptying devices for liquid products including vapour return
- CEN EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
- BSI BS EN 12561-2 Railway applications - Tank wagons Part 2: Bottom emptying devices for liquid products including vapour return - CORR: August 31, 2011
- CEN EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
- CEN EN 12561-2 Railway applications - Tank wagons - Part 2: Bottom emptying devices for liquid products including vapour return
- CEN EN 12561-2 Railway applications - Tank wagons - Part 2: Bottom emptying devices for liquid products including vapour return
- CEN EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
- BSI BS EN 12561-2 Railway applications - Tank wagons Part 2: Bottom emptying devices for liquid products including vapour return - CORR: August 31, 2011
- CEN EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
- BSI BS EN 12561-2 Railway applications - Tank wagons Part 2: Bottom emptying devices for liquid products including vapour return - CORR: August 31, 2011
- ISO 4200 Plain End Steel Tubes, Welded and Seamless - General Tables of Dimensions and Masses per Unit Length - Fourth Edition; Replaces ISO 134: 1973 and ISO 336: 1976
- ISO 21049 Pumps Shaft sealing systems for centrifugal and rotary pumps - First Edition
- ASME B16.11 Forged Fittings, Socket-Welding and Threaded
- Картотека зарубежных и международных стандартов
ASTM International
Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
N A182/A182M REV A
Annotation
This specification2 covers forged low alloy and stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts to specified dimensions or to dimensional standards, such as the ASME specifications that are referenced in Section 2.
For bars and products machined directly from bar (other than those directly addressed by this specification; see 6.4), refer to Specifications A479/A479M and A739 for the similar grades available in those specifications. Products made to this specification are limited to a maximum weight of 10 000 lb [4540 kg]. For larger products and products for other applications, refer to Specifications A336/A336M and A965/ A965M for the similar ferritic and austenitic grades, respectively, available in those specifications.
Several grades of low alloy steels and ferritic, martensitic, austenitic, and ferritic-austenitic stainless steels are included in this specification. Selection will depend upon design and service requirements. Several of the ferritic/ austenitic (duplex) grades are also found in Specification A1049/A1049M.
Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified individually by the purchaser in the order.
This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.
The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
