DIN 16917-1 Pipes and fittings made of thermoplastic materials with profiled wall and smooth pipe inside - Large pipes over DN 1200 for underground installation - Part 1: General requirements and performance characteristics
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- DIN SPEC 19674-2 Plastics piping systems made from glass fibre reinforced polyethylene (PE-GF) for water supply and for drainage and sewerage under pressure - Part 2: Pipes
- 23
- DIN SPEC 19674-2 Plastics piping systems made from glass fibre reinforced polyethylene (PE-GF) for water supply and for drainage and sewerage under pressure - Part 2: Pipes
- 23.040
- DIN SPEC 19674-2 Plastics piping systems made from glass fibre reinforced polyethylene (PE-GF) for water supply and for drainage and sewerage under pressure - Part 2: Pipes
- 23.040.20
- DIN EN ISO 9241-303 Ergonomics of human-system interaction - Part 303: Requirements for electronic visual displays (ISO 9241-303:2011)
- ISO 9241-302 Ergonomics of human-system interaction — Part 302: Terminology for electronic visual displays - First Edition
- ISO 9241-306 Ergonomics of human-system interaction — Part 306: Field assessment methods for electronic visual displays - First Edition
- ISO 9241-302 Ergonomics of human-system interaction — Part 302: Terminology for electronic visual displays - First Edition
- ISO 9241-302 Ergonomics of human-system interaction — Part 302: Terminology for electronic visual displays - First Edition
- ISO 9241-306 Ergonomics of human-system interaction — Part 306: Field assessment methods for electronic visual displays - First Edition
- ISO 9241-306 Ergonomics of human-system interaction — Part 306: Field assessment methods for electronic visual displays - First Edition
- DIN EN ISO 11296-7 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes (ISO 11296-7:2011)
- DIN EN ISO 9969 Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2007)
- DIN 16917-2 Pipes and fittings made of thermoplastic materials with profiled wall and smooth pipe inside - Large pipes over DN 1200 for underground installation - Part 2: Specifications for pipes and fittings
- Картотека зарубежных и международных стандартов
Deutsches Institut fur Normung e. V.
Pipes and fittings made of thermoplastic materials with profiled wall and smooth pipe inside - Large pipes over DN 1200 for underground installation - Part 1: General requirements and performance characteristics
N 16917-1
Annotation
This standard, in conjunction with DIN 16917-2, applies to pipes made of thermoplastic materials with profiled walls and smooth pipe inside and made of the following materials: polyethylene (PE 80, PE 100 and PE-HD), polypropylene (PP), homopolymer and copolymer and unplasticized polyvinyl chloride (PVC-U), with a nominal diameter greater than 1 200 mm, intended for underground installation. It also applies to fittings manufactured from these pipes.
This standard contains general requirements and performance characteristics for large pipes and fittings made of thermoplastic materials with profiled walls and smooth pipe inside for underground uses
Автоматический перевод:
Трубы и детали, сделанные из термопластических материалов с профилируемой стеной и гладкой трубой внутри - Большие трубы за 1200 DN для подземной установки - Часть 1: Общие требования и технические характеристики
Этот стандарт, в сочетании с DIN 16917-2, относится к трубам, сделанным из термопластических материалов с профилируемыми стенами и гладкой трубой внутри и сделанный из следующих материалов: полиэтилен (PE 80, PE 100 и PE-HD), полипропилен (PP), гомополимер и сополимер и не придавший пластичность поливинилхлорид (PVC-U), с номинальным диаметром, больше, чем 1 200 мм, предназначенных для подземной установки. Это также относится к деталям, произведенным от этих труб.
