ASTM B927/B927M Standard Specification for Brass Rod, Bar, and Shapes
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- ASTM B983 REV A Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube
- 23
- ASTM B983 REV A Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube
- 23.040
- ASTM B983 REV A Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube
- 23.040.15
- ASTM E1268 Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures
- ASTM E3 Standard Guide for Preparation of Metallographic Specimens
- ASTM B961 Standard Specification for Silver Coated Copper and Copper Alloy Stranded Conductors for Electronic Space Application
- ASTM E3 Standard Guide for Preparation of Metallographic Specimens
- ASTM E3 Standard Guide for Preparation of Metallographic Specimens
- ASTM B961 Standard Specification for Silver Coated Copper and Copper Alloy Stranded Conductors for Electronic Space Application
- ASTM B961 Standard Specification for Silver Coated Copper and Copper Alloy Stranded Conductors for Electronic Space Application
- ASTM B624 Standard Specification for High-Strength, High-Conductivity Copper-Alloy Wire for Electronic Application
- ASTM E8/E8M REV A Standard Test Methods for Tension Testing of Metallic Materials
- ASTM B706 Standard Specification for Seamless Copper Alloy (UNS No. C69100) Pipe and Tube
- ASTM B193 Standard Test Method for Resistivity of Electrical Conductor Materials
- ASTM B249/B249M Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
- Картотека зарубежных и международных стандартов
ASTM International
Standard Specification for Brass Rod, Bar, and Shapes
N B927/B927M
Annotation
This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, C27400, C27450, C27451, C27453, and C28500.
Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
*A Summary of Changes section appears at the end of this standard
Автоматический перевод:
Стандартная спецификация для прутковой латуни, панели и форм
Эта спецификация устанавливает требования для прутковой латуни (круглый, шестиугольный, и восьмиугольный), панель (прямоугольный и квадратный), и формы Сплавов UNS C21000, C22000, C23000, C24000, C26000, C26800, C27000, C27400, C27450, C27451, C27453 и C28500.
Модули — значения, утвержденные или в единицах СИ или в inchpound модулях, должны рассматриваться отдельно как стандарт. Значения, утвержденные в каждой системе, не могут быть точными эквивалентами; поэтому, каждая система должна использоваться независимо от другого. Объединение значений от этих двух систем может привести к несоответствию со стандартом.
