ASD-STAN PREN 4835 Aerospace series - Installation and removal requirements for Ring locked fitting and reducer, 24° Cone up to 35 000 kPa (5 080 psi) - Inch Series - Edition P1
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- SAE AS5551A Fitting Assembly – 24Degree Cone Flareless per AS5827, 5080 psi, Port Connection Port Preparation, Installation and Removal of AS5550 and AS5865
- ASD-STAN PREN 4836 Aerospace series - Adaptor, Pipe coupling 24°Cone up to 35 000 kPa (5 080 psi) Ringlocked fitting Reducer-Flareless End - Inch Series - Extra Fine Thread Pitch - Edition P1
- ASD-STAN PREN 4835 Aerospace series - Installation and removal requirements for Ring locked fitting and reducer, 24° Cone up to 35 000 kPa (5 080 psi) - Inch Series - Edition P1
- ASD-STAN PREN 4833 Aerospace series - Pipe coupling 24° Cone up to 35 000 kPa (5 080 psi) Ring locked fitting - Flareless End - Inch Series - Extra Fine Thread Pitch - Edition P1
- ASD-STAN PREN 4836 Aerospace series - Adaptor, Pipe coupling 24°Cone up to 35 000 kPa (5 080 psi) Ringlocked fitting Reducer-Flareless End - Inch Series - Extra Fine Thread Pitch - Edition P1
- ASD-STAN PREN 4835 Aerospace series - Installation and removal requirements for Ring locked fitting and reducer, 24° Cone up to 35 000 kPa (5 080 psi) - Inch Series - Edition P1
- ASD-STAN PREN 4833 Aerospace series - Pipe coupling 24° Cone up to 35 000 kPa (5 080 psi) Ring locked fitting - Flareless End - Inch Series - Extra Fine Thread Pitch - Edition P1
- CEN EN 6123 Aerospace series - Fitting end, 24° internal cone, external thread, flareless type - Extra fine thread pitch - Inch series - Design standard
- 49
- SAE AS5551A Fitting Assembly – 24Degree Cone Flareless per AS5827, 5080 psi, Port Connection Port Preparation, Installation and Removal of AS5550 and AS5865
- Картотека зарубежных и международных стандартов
Aerospace and Defence Industries Association of Europe - Standardization
Aerospace series - Installation and removal requirements for Ring locked fitting and reducer, 24° Cone up to 35 000 kPa (5 080 psi) - Inch Series - Edition P1
N PREN 4835
Annotation
This standard specifies the installation and removal requirements for adaptors and reducers, threaded, with lockring for pipe couplings 24° according to EN 4833 and EN 4836.
This standard establishes an accurate procedure of adaptor installation, removal and reinstallation to ensure the repeatability of the installation operation and to ensure the effective compliance to sealing and locking requirements.
The adaptor shown on all Figures of this standard is given as an example for the 24° internal cone interface according to EN 6123.
This procedure is used for adaptors 24°, for nominal pressure up to 35 000 kPa (5 080 psi).
Автоматический перевод:
Космический ряд - Установка и требования удаления для Кольца, захваченного, соответствуя и редуктора, Конус на 24 ° до 35 000 кПа (5 080 фунтов на квадратный дюйм) - Ряд Дюйма - Издание P1
Этот стандарт определяет требования установки и удаления для адаптеров и редукторов, резьбовых, со стопорным кольцом для трубных соединений 24 ° согласно EN 4833 и EN 4836.
Этот стандарт устанавливает точный порядок установки адаптера, удаления и переустановки, чтобы гарантировать воспроизводимость инсталляционной работы и гарантировать эффективное соблюдение запечатывания и захвата требований.
