GMW GMW16535 Metallurgical and Mechanical Properties of Wheel Bolts and Studs - Issue 2; English
Список продуктов
Данный раздел/документ содержится в продуктах:
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- ISO 6336-2 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) - Second Edition
- ISO 6336-5 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials - Second Edition
- BSI BS ISO 10300-2 Calculation of Load Capacity of Bevel Gears - Part 2: Calculation of Surface Durability (Pitting)
- ISO 6336-5 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials - Second Edition
- 21
- ISO 6336-2 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) - Second Edition
- ISO 6336-5 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials - Second Edition
- BSI BS ISO 10300-2 Calculation of Load Capacity of Bevel Gears - Part 2: Calculation of Surface Durability (Pitting)
- ISO 6336-5 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials - Second Edition
- 21.200
- ISO 6336-2 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) - Second Edition
- ISO 6336-5 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials - Second Edition
- ISO 6336-2 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) - Second Edition
- ISO 6336-2 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) - Second Edition
- BSI BS ISO 10300-2 Calculation of Load Capacity of Bevel Gears - Part 2: Calculation of Surface Durability (Pitting)
- ISO 6336-5 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials - Second Edition
- ISO 6336-5 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials - Second Edition
- BSI BS ISO 10300-3 Calculation of Load Capacity of Bevel Gears - Part 3: Calculation of Tooth Root Strength
- ISO 10300-1 Calculation of load capacity of bevel gears - Part 1: Introduction and general influence factors - Second Edition
- BSI BS ISO 6336-5 Calculation of load capacity of spur and helical gears - Part 5: Strength and quality of materials
- ISO 683-1 Heat-treatable steels, alloy steels and free-cutting steels - Part 1: Non-alloy steels for quenching and tempering - Third Edition
- ISO 6336-2 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) - Second Edition
- Картотека зарубежных и международных стандартов
Ссылается на
- В списке элементов: 4
- ISO 683-1 Heat-treatable steels, alloy steels and free-cutting steels - Part 1: Non-alloy steels for quenching and tempering - Third EditionПоддающиеся обработке с теплом стали, легированные стали и автоматные стали - Часть 1: нелегированные стали для подавления и закалки - Третий Выпуск
Карточка документа - ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread - Cinquieme editionМеханические свойства застежек сделаны из углеродистой стали и легированной стали - Часть 1: Болты, винты и гвоздики с указанными имущественными классами - Крупной резьбой и прекрасной резьбой подачи - Cinquieme edition
На основе ISO 898-1 разработан ГОСТ ISO 898-1-2014 (IDT)ГОСТ ISO 898-1-2014 (IDT) - ISO 8992 Fasteners General requirements for bolts, screws, studs and nuts - Second EditionЗастежки Общие требования для болтов, винтов, гвоздиков и гаек - Второй Выпуск
На основе ISO 8992 разработаны ГОСТ Р ИСО 8992-2011 (IDT); ГОСТ ISO 8992-2015 (IDT)ГОСТ ISO 8992-2015 (IDT) - ISO 6157-3 Fasteners - Surface Discontinuities - Part 3: Bolts, Screws and Studs for Special Requirements First EditionЗастежки - нарушения сплошности поверхности - часть 3: болты, винты и гвоздики для особых требований первый выпуск
На основе ISO 6157-3 разработан ГОСТ ISO 6157-3-2014 (IDT)ГОСТ ISO 6157-3-2014 (IDT)
