CEN EN ISO 10675-1 Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 1: Steel, nickel, titanium and their alloys
Список продуктов
Данный раздел/документ содержится в продуктах:
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- CEN EN ISO 9934-1 Non-Destructive Testing - Magnetic Particle Testing - Part 1: General Principles
- 19
- BSI BS EN ISO 4590 Rigid cellular plastics Determination of the volume percentage of open cells and of closed cells
- 83
- BSI BS EN ISO 4590 Rigid cellular plastics Determination of the volume percentage of open cells and of closed cells
- 83.100
- BSI BS EN ISO 4590 Rigid cellular plastics Determination of the volume percentage of open cells and of closed cells
- ASTM D3664 Standard Specification for Biaxially Oriented Polymeric Resin Film for Capacitors in Electrical Equipment
- ASTM D3985 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
- BSI BS EN 14318-1 Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam dispensed system before installation
- BSI BS EN ISO 4590 Rigid cellular plastics Determination of the volume percentage of open cells and of closed cells
- BSI BS EN 14318-1 Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam dispensed system before installation
- ASTM D3985 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
- ASTM D3985 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
- BSI BS EN 14318-1 Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam dispensed system before installation
- BSI BS EN ISO 4590 Rigid cellular plastics Determination of the volume percentage of open cells and of closed cells
- BSI BS EN 14318-1 Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam dispensed system before installation
- BSI BS EN 14318-1 Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam dispensed system before installation
- BSI BS EN ISO 4590 Rigid cellular plastics Determination of the volume percentage of open cells and of closed cells
- BSI BS EN 253 + A2 District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene - AMD: April 30, 2013; AMD: October 31, 2015
- BSI BS EN 448 District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
- Картотека зарубежных и международных стандартов
На него ссылаются
- В списке элементов: 2
- CEN EN 378-2 Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentationОхлаждение систем и тепловых насосов - Требований техники безопасности и экологических требований - Часть 2: Дизайн, строительство, тестирование, маркировка и документация
Карточка документа - CEN EN 14276-2 Pressure equipment for refrigerating systems and heat pumps - Part 2: Piping - General requirements - Incorporates Amendment A1: 2011Прессовое оборудование для охлаждения систем и тепловых насосов - Часть 2: Трубопровод - Общие требования - Включают Поправку A1: 2011
Карточка документа
