ASTM B111/B111M Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- IEC 60079-10-2 Explosive atmospheres – Part 10-2: Classification of areas – Combustible dust atmospheres - Edition 1.0
- 29
- IEC 60079-10-2 Explosive atmospheres – Part 10-2: Classification of areas – Combustible dust atmospheres - Edition 1.0
- 29.260
- IEC 60079-10-2 Explosive atmospheres – Part 10-2: Classification of areas – Combustible dust atmospheres - Edition 1.0
- 29.260.20
- ISO FDIS 24817 Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection
- ASME B31G Manual for Determining the Remaining Strength of Corroded Pipelines
- ASME PTB-9 ASME Pipeline Standards Compendium
- ASME B31.8S Managing System Integrity of Gas Pipelines - Supplement to ASME B31.8
- ASME PTB-9 ASME Pipeline Standards Compendium
- ASME B31G Manual for Determining the Remaining Strength of Corroded Pipelines
- ASME B31G Manual for Determining the Remaining Strength of Corroded Pipelines
- ASME PTB-9 ASME Pipeline Standards Compendium
- ASME B31.8S Managing System Integrity of Gas Pipelines - Supplement to ASME B31.8
- ASME PTB-9 ASME Pipeline Standards Compendium
- ASME PTB-9 ASME Pipeline Standards Compendium
- ASME B31.8S Managing System Integrity of Gas Pipelines - Supplement to ASME B31.8
- ASME B31.8S Managing System Integrity of Gas Pipelines - Supplement to ASME B31.8
- DIN EN 14161 Petroleum and natural gas industries - Pipeline transportation systems (ISO 13623:2009 modified) (includes Amendment A1:2015)
- ISO 10439 Petroleum, Chemical and Gas Service Industries - Centrifugal Compressors - First Edition
- ASTM A522/A522M Standard Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service
- ASME B31.5 Refrigeration Piping and Heat Transfer Components
- Картотека зарубежных и международных стандартов
ASTM International
Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock
N B111/B111M
Annotation
This specification2 establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys up to 31?8 in. [80 mm] inclusive, in diameter, for use in surface condensers, evaporators, and heat exchangers. The following coppers and copper alloys are specified:3
Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
The following safety hazards caveat pertains only to the test methods portion, Section 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products in your state or country may be prohibited by law.)
2 For ASME Boiler and Pressure Vessel Code applications, see related Specification SB-111 in Section II of the Code.
3 The UNS system for copper and copper alloys (see Practice E527) is a simple expansion of the former standard designation system accomplished by the addition of a prefix “C” and a suffix “00.” The suffix can be used to accommodate composition variations of the base alloy
