ASTM A1031/A1031M Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- ASTM A507 Standard Specification for Drawing Alloy Steel, Sheet and Strip, Hot-Rolled and Cold-Rolled
- ASTM A505 Standard Specification for Steel, Sheet and Strip, Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
- ASTM A1031/A1031M Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled
- SNV SN EN 13611+A2 Safety and control devices for gas burners and gas burning appliances - General requirements
- ASTM A707/A707M Standard Specification for Forged Carbon and Alloy Steel Flanges for Low-Temperature Service
- 23
- SNV SN EN 13611+A2 Safety and control devices for gas burners and gas burning appliances - General requirements
- ASTM A707/A707M Standard Specification for Forged Carbon and Alloy Steel Flanges for Low-Temperature Service
- 23.060
- SNV SN EN 13611+A2 Safety and control devices for gas burners and gas burning appliances - General requirements
- ASTM A707/A707M Standard Specification for Forged Carbon and Alloy Steel Flanges for Low-Temperature Service
- SNV SN EN 13611+A2 Safety and control devices for gas burners and gas burning appliances - General requirements
- SNV SN EN 13611+A2 Safety and control devices for gas burners and gas burning appliances - General requirements
- ASTM A707/A707M Standard Specification for Forged Carbon and Alloy Steel Flanges for Low-Temperature Service
- ASME BPVC IX TRAINING ASME ASSESSMENT-BASED COURSE: ESSENTIALS - BPV CODE, SECTION IX: WELDING & BRAZING QUALIFICATIONS - SINGLE-USER LICENSE (COURSE NUMBER: ZABC18) - PDHs: 2.00
- ASTM A20/A20M Standard Specification for General Requirements for Steel Plates for Pressure Vessels
- ASTM A506 Standard Specification for Alloy and Structural Alloy Steel, Sheet and Strip, Hot-Rolled and Cold-Rolled
- Картотека зарубежных и международных стандартов
ASTM International
Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Alloy, Drawing Steel and Structural Steel, Hot-Rolled
N A1031/A1031M
Annotation
This specification covers hot-rolled, heavy thickness coils beyond the size limits of Specifications A506 and A507.
The product is available in three designations: Alloy Steel, Drawing Steel, and Structural Alloy Steel.
Alloy steel is furnished to chemical composition requirements and is intended primarily for general or miscellaneous use where bending and moderate forming is a requirement.
Drawing steel is produced principally for applications involving severe cold plastic deformation such as deep drawn or severely formed parts.
Drawing steel may be furnished in several conditions, heat treatments, surface finishes, and edges, as specified herein.
Structural steel is furnished to chemical composition requirements and to specific mechanical property requirements which may include tension tests, hardness tests, or other commonly accepted mechanical tests.
The formability of structural steel decreases with increasing yield strength or hardness. Therefore, product design in relation to the mechanical properties of the grade used must be considered.
Sheet and strip in coils of sizes noted in 1.6 are covered by this specification only with the following provisions:
The material is not to be converted into steel plates for structural or pressure vessel use unless tested in complete accordance with the appropriate sections of Specifications A6/A6M (plates provided from coils) or A20/A20M (plates produced from coils). A plate produced in this manner is no longer governed by this sheet steel specification and since this material is now plate, the appropriate plate standard must now apply.



