ASTM C786/C786M Standard Test Method for Fineness of Hydraulic Cement and Raw Materials by the 300-mue m (No. 50), 150-mue m (No. 100), and 75-mue m (No. 200) Sieves by Wet Methods
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- ASTM F1412 Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems
- 23
- ASTM F441/F441M Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80
- ASTM D1785 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120
- ASTM F480 Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80
- ASTM D1785 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120
- ASTM D1785 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120
- ASTM F480 Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80
- ASTM F480 Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80
- ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
- ASTM F2390 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content
- ASTM D2774 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
- ASTM E11 Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
- Картотека зарубежных и международных стандартов
ASTM International
Standard Test Method for Fineness of Hydraulic Cement and Raw Materials by the 300-mue m (No. 50), 150-mue m (No. 100), and 75-mue m (No. 200) Sieves by Wet Methods
N C786/C786M
Annotation
This test method covers wet sieving techniques for determination of fineness of hydraulic cement and raw materials by means of the 300-?m (No. 50), the 150-?m (No. 100), and the 75-?m (No. 200) sieves.
The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10 of measurements made in other units. Values are stated in SI units when inch-pound units are not used in practice.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
*A Summary of Changes section appears at the end of this standard.
Автоматический перевод:
Стандартный Метод тестирования для Тонкости Гидравлического Цемента и Сырья 300-mue m (№ 50), 150-mue m (№ 100) и 75-mue m (№ 200) Решета Влажными Методами
