ASTM F2735 Standard Specification for Plastic Insert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- SNV SN ISO 161-1 Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Part 1: Metric series
- 23
- SNV SN ISO 161-1 Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Part 1: Metric series
- 23.040
- ISO 12500-1 Filters for compressed air — Test methods — Part 1: Oil aerosols - First Edition
- ISO 5782-2 Pneumatic Fluid Power - Compressed Air Filters - Part 2: Test Methods to determine the Main Characteristics to Be Included in Supplier?s Literature - First Edition
- BSI BS ISO 5782-1 Pneumatic Fluid Power - Compressed Air Filters - Part 1: Main Characteristics to be Included in Supplier's Literature and Product-Marking Requirements
- ISO 5782-2 Pneumatic Fluid Power - Compressed Air Filters - Part 2: Test Methods to determine the Main Characteristics to Be Included in Supplier?s Literature - First Edition
- ISO 5782-2 Pneumatic Fluid Power - Compressed Air Filters - Part 2: Test Methods to determine the Main Characteristics to Be Included in Supplier?s Literature - First Edition
- BSI BS ISO 5782-1 Pneumatic Fluid Power - Compressed Air Filters - Part 1: Main Characteristics to be Included in Supplier's Literature and Product-Marking Requirements
- BSI BS ISO 5782-1 Pneumatic Fluid Power - Compressed Air Filters - Part 1: Main Characteristics to be Included in Supplier's Literature and Product-Marking Requirements
- ISO 2944 Fluid Power Systems and Components - Nominal Pressures - Second Edition
- SNV SN ISO 4065 Thermoplastic pipes - Universal wall thickness table
- ISO 161-2 Thermoplastics Pipes for the Conveyance of Fluids - Nominal Outside Diameters and Nominal Pressures - Part 2: Inch-Based Series - Second Edition
- ASTM F876 REV A Standard Specification for Crosslinked Polyethylene (PEX) Tubing
- Картотека зарубежных и международных стандартов
ASTM International
Standard Specification for Plastic Insert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing
N F2735
Annotation
This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings for three sizes (1?2, 3?4, and 1) of cross-linked polyethylene (PEX) and polyethylene of raised temperature (PE-RT) plastic tubing. These fittings are intended for use in 100 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180°F (82°C). Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and rings.
Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
The following is an index of the appendix in this specification.
The following precautionary caveat pertains only to the test method portions, Sections 11 and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
*A Summary of Changes section appears at the end of this standard
Автоматический перевод:
Стандартная спецификация для пластмассовых деталей вставки для SDR9 перекрестный сопряженный полиэтилен (PEX) и полиэтилен выпуклой температуры (PERT) трубка
