UNI EN 40-2 Lighting columns - Part 2: General requirements and dimensions
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- DIN EN 40-3-3 Lighting columns - Part 3-3: Design and verification - Verification by calculation
- CEN EN 40-3-1 Lighting columns - Part 3-1: Design and verification - Specification for characteristic loads
- 93
- DIN EN 40-3-3 Lighting columns - Part 3-3: Design and verification - Verification by calculation
- CEN EN 40-3-1 Lighting columns - Part 3-1: Design and verification - Specification for characteristic loads
- 93.080
- DIN EN 40-3-3 Lighting columns - Part 3-3: Design and verification - Verification by calculation
- CEN EN 40-3-1 Lighting columns - Part 3-1: Design and verification - Specification for characteristic loads
- 93.080.40
- DIN EN 40-3-3 Lighting columns - Part 3-3: Design and verification - Verification by calculation
- CEN EN 40-3-1 Lighting columns - Part 3-1: Design and verification - Specification for characteristic loads
- DIN EN 40-3-3 Lighting columns - Part 3-3: Design and verification - Verification by calculation
- DIN EN 40-3-3 Lighting columns - Part 3-3: Design and verification - Verification by calculation
- DIN EN 40-3-3 Lighting columns - Part 3-3: Design and verification - Verification by calculation
- CEN EN 40-3-1 Lighting columns - Part 3-1: Design and verification - Specification for characteristic loads
- CEN EN 40-3-3 Lighting columns - Part 3-3: Design and verification - Verification by calculation
- DIN EN 40-3-2 Lighting columns - Part 3-2: Design and verification - Verification by testing
- CEN EN 40-7 Lighting columns - Part 7: Requirements for fibre reinforced polymer composite lighting columns
- DIN EN 40-3-1 Lighting columns - Part 3-1: Design and verification - Specification for characteristic loads
- CEN EN 12767 Passive safety of support structures for road equipment - Requirements, classification and test methods
- DIN EN 40-3-3 Lighting columns - Part 3-3: Design and verification - Verification by calculation
- Картотека зарубежных и международных стандартов
Ente Nazionale Italiano di Unificazione
Lighting columns - Part 2: General requirements and dimensions
N UNI EN 40-2
Annotation
This document specifies the requirements and dimensions for lighting columns, brackets, base compartments, cableways and earthing terminals. It applies to post top columns not exceeding 20 m height for post top lanterns and columns with brackets not exceeding 18 m height for side entry lanterns.
This Part does not attempt to restrict the actual appearance or shape of the column or bracket. The majority of lighting columns are normally of a stepped tubular, round, octagonal or polygonal crosssection. Lighting columns may be manufactured from materials other than those listed in the foreword (e.g. wood, plastic, cast iron) or in other forms (e.g. lattice and telescopic).
This document specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under vehicle impact (passive safety) in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this document or available in separate documents.
Автоматический перевод:
Фонарные столбы - Часть 2: Общие требования и измерения
Этот документ определяет требования и измерения для фонарных столбов, кронштейнов, основных отсеков, кабелепроводов и клемм заземления. Это применяется к почтовым колонкам вершины, не превышающим 20 м высотой для почтовых фонарей вершины и колонок с кронштейнами, не превышающими 18 м высотой для фонарей входа стороны.
