ASTM D5363 Standard Specification for Anaerobic Single-Component Adhesives (AN)
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- ASTM F2080 Standard Specification for Cold-Expansion Fittings With Metal Compression-Sleeves for Cross-Linked Polyethylene (PEX) Pipe
- 23
- ASTM F2080 Standard Specification for Cold-Expansion Fittings With Metal Compression-Sleeves for Cross-Linked Polyethylene (PEX) Pipe
- 23.040
- ASTM F2080 Standard Specification for Cold-Expansion Fittings With Metal Compression-Sleeves for Cross-Linked Polyethylene (PEX) Pipe
- 23.040.40
- ASTM F480 Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80
- ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
- ASTM F1807 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
- ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
- ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
- ASTM F1807 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
- ASTM F1807 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
- ASTM A276/A276M REV A Standard Specification for Stainless Steel Bars and Shapes
- ASTM F1018 REV A Standard Specification for Steel Emergency Gear Stowage Locker
- ASTM B36/B36M Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar
- ASTM D5363 Standard Specification for Anaerobic Single-Component Adhesives (AN)
- ASTM D5657 Standard Test Method for Fluid Tightness Ability of Adhesives Used on Threaded Fasteners
- Картотека зарубежных и международных стандартов
ASTM International
Standard Specification for Anaerobic Single-Component Adhesives (AN)
N D5363
Annotation
This specification covers single-component anaerobic adhesives suitable for locking, sealing, and retaining threaded or cylindrical assemblies. The adhesives are cured to a solid state when confined between closely fitting active metal surfaces.
This specification is intended to be a means of classifying anaerobic adhesives. It is not intended for engineering design purposes.
This specification is intended to replace Military Specifications MIL-S-22473, MIL-S-46163, and MIL-R-46082.
The values stated in SI units are to be regarded as the standard.
The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Автоматический перевод:
Стандартная спецификация для анаэробных адгезивов однородной нагрузки (AN)
Эта спецификация покрывает однокомпонентные анаэробные адгезивы, подходящие для блокировки, изоляции и сохранения потоковых или цилиндрических блоков. Адгезивы исправлены к твердому телу, когда ограничено между обтягивающим образом активными металлическими поверхностями.
