ISO 3503 Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending - Second Edition
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- CEN EN 12117 Platics Piping Systems - Fittings, Valves and Ancillaries - Determination of Gaseous Flow Rate/Pressure Drop Relationships
- 23
- CEN EN 12117 Platics Piping Systems - Fittings, Valves and Ancillaries - Determination of Gaseous Flow Rate/Pressure Drop Relationships
- 23.040
- CEN EN 12117 Platics Piping Systems - Fittings, Valves and Ancillaries - Determination of Gaseous Flow Rate/Pressure Drop Relationships
- BSI BS EN 12117 Plastics Piping Systems - Fittings, Valves and Ancillaries - Determination of Gaseous Flow Rate/Pressure Drop Relationships
- BSI BS ISO 10838-3 Mechanical Fittings for Polyethylene Piping Systems for the Supply of Gaseous Fuels - Part 3: Thermoplastic Fittings for Pipes of Nominal Outside Diameter Less Than or Equal to 63mm
- 23.060
- BSI BS EN 12117 Plastics Piping Systems - Fittings, Valves and Ancillaries - Determination of Gaseous Flow Rate/Pressure Drop Relationships
- BSI BS ISO 10838-3 Mechanical Fittings for Polyethylene Piping Systems for the Supply of Gaseous Fuels - Part 3: Thermoplastic Fittings for Pipes of Nominal Outside Diameter Less Than or Equal to 63mm
- BSI BS EN 12117 Plastics Piping Systems - Fittings, Valves and Ancillaries - Determination of Gaseous Flow Rate/Pressure Drop Relationships
- BSI BS ISO 10838-3 Mechanical Fittings for Polyethylene Piping Systems for the Supply of Gaseous Fuels - Part 3: Thermoplastic Fittings for Pipes of Nominal Outside Diameter Less Than or Equal to 63mm
- BSI BS ISO 10838-3 Mechanical Fittings for Polyethylene Piping Systems for the Supply of Gaseous Fuels - Part 3: Thermoplastic Fittings for Pipes of Nominal Outside Diameter Less Than or Equal to 63mm
- BSI BS ISO 10838-1 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63mm
- Картотека зарубежных и международных стандартов
International Organization for Standardization
Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending - Second Edition
N 3503
Annotation
This International Standard specifies a method for checking the leaktightness under internal pressure of assembled joints between mechanical fittings and plastic pressure pipes when subjected to bending. It defines the calculation method for the average bending radius and how to perform this bending.
Checking of the leaktightness under internal pressure is carried out in accordance with the method given in ISO 3458.
This test method is not applicable to fusion-welded joints
Автоматический перевод:
Трубопроводные системы пластмасс - Механические соединения между деталями и нагнетательными трубами - Методом испытаний для герметичности под внутренним давление сборок, подвергнутых изгибу - Второй Выпуск
Этот Международный стандарт определяет метод для проверки герметичности под внутренним давление собранных соединений между механическими деталями и пластмассовыми нагнетательными трубами, когда подвергнуто изгибу. Это определяет метод расчета для среднего радиуса изгиба и как выполнить этот изгиб.
