SNV SN EN ISO 13967 Thermoplastics fittings - Determination of ring stiffness
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- SNV SN EN ISO 13967 Thermoplastics fittings - Determination of ring stiffness
- 23
- SNV SN EN ISO 1167-1 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
- SNV SN EN 12842 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
- SNV SN EN 12201-2+A1 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
- ISO 13968 Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility - Second Edition
- SNV SN EN 12201-2+A1 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
- SNV SN EN 12842 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
- SNV SN EN 12842 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
- SNV SN EN 12201-2+A1 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
- ISO 13968 Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility - Second Edition
- SNV SN EN 12201-2+A1 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
- SNV SN EN 12201-2+A1 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
- ISO 13968 Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility - Second Edition
- ISO 13968 Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility - Second Edition
- CEN EN 14758-1 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
- ISO 13967 Thermoplastics fittings — Determination of ring stiffness - Second Edition
- ISO 9969 Thermoplastics pipes — Determination of ring stiffness - Second Edition
- Картотека зарубежных и международных стандартов
Schweizerische Normen-Vereinigung
Thermoplastics fittings - Determination of ring stiffness
N SN EN ISO 13967
Annotation
This International Standard specifies a method of determining the ring stiffness of bends and branches made from thermoplastic material and for use with plastics pipes having a circular cross-section.
The method can be used to determine the stiffness of bends, equal branches and unequal branches, provided the fitting allows a diametric deflection of at least 4 %.
NOTE 1 If a fitting has the same wall thickness, wall construction, material and diameter as a pipe tested according to ISO 9969, then, because of its geometry, its stiffness can be equal to or greater than that of the pipe. In this case, the fitting can be classified as having the same stiffness class as the pipe, without testing.
NOTE 2 Any unequal branch can be expected to have at least the same stiffness as an equal branch, provided that it has the same main diameter, wall construction and material as the equal branch.
NOTE 3 A reducer having the same wall thickness, wall construction and material in the transition zone as a tested bend or branch can be expected to have at least the same stiffness as the tested bend or branch with the largest diameter of that reducer.
NOTE 4 The result of the test reflects the resistance the fitting has against deflection when installed. Advice on the significance of the test result is given in Annex A.
Автоматический перевод:
