DIN ISO 48 Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10 IRHD and 100 IRHD) (ISO 48:2010)
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- DIN 58729 Production in optical engineering - Ball seats
- DIN 58727-1 Production in optical engineering - Surfacing pins for optics processing machines - Part 1: Without ball point cemented metal carbide
- 37
- DIN 58729 Production in optical engineering - Ball seats
- DIN 58727-1 Production in optical engineering - Surfacing pins for optics processing machines - Part 1: Without ball point cemented metal carbide
- 37.020
- DIN 58729 Production in optical engineering - Ball seats
- DIN 58727-1 Production in optical engineering - Surfacing pins for optics processing machines - Part 1: Without ball point cemented metal carbide
- DIN 58727-1 Production in optical engineering - Surfacing pins for optics processing machines - Part 1: Without ball point cemented metal carbide
- DIN 58729 Production in optical engineering - Ball seats
- DIN 58727-1 Production in optical engineering - Surfacing pins for optics processing machines - Part 1: Without ball point cemented metal carbide
- DIN 58729 Production in optical engineering - Ball seats
- DIN 58727-1 Production in optical engineering - Surfacing pins for optics processing machines - Part 1: Without ball point cemented metal carbide
- DIN 58751-2 Production in optical engineering - Abrasives for optical engineering - Part 2: Testing methods
- DIN ISO 7619-2 Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Part 2: IRHD pocket meter method (ISO 7619-2:2010)
- DIN ISO 48 Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10 IRHD and 100 IRHD) (ISO 48:2007)
- DIN ISO 27588 Rubber, vulcanized or thermoplastic - Determination of dead-load hardness using the very low rubber hardness (VLRH) scale (ISO 27588:2012)
- DIN 58729 Production in optical engineering - Ball seats
- Картотека зарубежных и международных стандартов
Deutsches Institut fur Normung e. V.
Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10 IRHD and 100 IRHD) (:2010)
N ISO 48
Annotation
This International Standard specifies four methods for the determination of the hardness of vulcanized or thermoplastic rubbers on flat surfaces (standard-hardness methods) and four methods for the determination of the apparent hardness of curved surfaces (apparent-hardness methods). The hardness is expressed in international rubber hardness degrees (IRHD). The methods cover the hardness range from 10 IRHD to 100 IRHD.
These methods differ primarily in the diameter of the indenting ball and the magnitude of the indenting force, these being chosen to suit the particular application. The range of applicability of each method is indicated in Figure 1.
This International Standard does not specify a method for the determination of hardness by a pocket hardness meter, which is described in ISO 7619-2.
This International Standard specifies the following four methods for the determination of standard hardness.
Method N (normal test) is appropriate for rubbers with a hardness in the range 35 IRHD to 85 IRHD, but can also be used for hardnesses in the range 30 IRHD to 95 IRHD.
Method H (high-hardness test) is appropriate for rubbers with a hardness in the range 85 IRHD to 100 IRHD.
Method L (low-hardness test) is appropriate for rubbers with a hardness in the range 10 IRHD to 35 IRHD.
Method M (microtest) is essentially a scaled-down version of the normal test method N, permitting the testing of thinner and smaller test pieces. It is appropriate for rubbers with a hardness in the range 35 IRHD to 85 IRHD, but can also be used for hardnesses in the range 30 IRHD to 95 IRHD.
