GMW GMW15745 GM Dimensional Engineering Supplier Minimum Requirements - Issue 3; English
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- GMW GMW15350 Interior Door Trim Assembly - Steady State Part Monitoring - Issue 3; English; GMW RESTRICTED/CONFIDENTIAL STANDARD – To purchase call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide
- GMW GMW14831 Specification for the Safety Belt Component - Issue 4; English; GMW RESTRICTED/CONFIDENTIAL STANDARD – To purchase call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide
- ASTM F1946/F1946M Standard Practice for Accelerated Testing of the Lightfastness of Ink Jet Prints Exposed to Indoor Fluorescent Lighting and Window–Filtered Daylight
- ASTM D4674 REV A Standard Practice for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments
- 87
- ASTM F1946/F1946M Standard Practice for Accelerated Testing of the Lightfastness of Ink Jet Prints Exposed to Indoor Fluorescent Lighting and Window–Filtered Daylight
- ASTM D4674 REV A Standard Practice for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments
- 87.080
- ASTM F1946/F1946M Standard Practice for Accelerated Testing of the Lightfastness of Ink Jet Prints Exposed to Indoor Fluorescent Lighting and Window–Filtered Daylight
- ASTM D4674 REV A Standard Practice for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments
- ASTM F1946/F1946M Standard Practice for Accelerated Testing of the Lightfastness of Ink Jet Prints Exposed to Indoor Fluorescent Lighting and Window–Filtered Daylight
- ASTM F1946/F1946M Standard Practice for Accelerated Testing of the Lightfastness of Ink Jet Prints Exposed to Indoor Fluorescent Lighting and Window–Filtered Daylight
- ASTM D4303 Standard Test Methods for Lightfastness of Colorants Used in Artists’ Materials
- ASTM D4674 REV A Standard Practice for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments
- ASTM D4674 REV A Standard Practice for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments
- ASTM D2244 REV A Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
- ASTM D4086 REV A Standard Practice for Visual Evaluation of Metamerism
- ASTM E1499 Standard Guide for Selection, Evaluation, and Training of Observers
- SAE J361 Procedure for Visual Evaluation of Interior and Exterior Automotive Trim
- GMW GMW14831 Specification for the Seat Belt Component - Issue 5; English; GMW RESTRICTED/CONFIDENTIAL STANDARD – To purchase call 1-800-854-7179 USA/Canada or 303-397-7956 Worldwide
- Картотека зарубежных и международных стандартов
General Motors Company
GM Dimensional Engineering Supplier Minimum Requirements - Issue 3; English
N GMW15745
Annotation
Introduction
Note: Nothing in this standard supercedes applicable laws and regulations.
Note: In the event of conflict between the English and domestic language, the English language shall take precedence.
Purpose. GM requires its production/design suppliers to adopt GM’s commitment to quality and expects the suppliers to conform to GM processes, policies and procedures. This portion of the Statement of Requirements (SOR) describes the minimum dimensional requirements/tasks that the awarded supplier is expected to perform.
Applicability. GM requires its production suppliers to adopt GM’s philosophy of total commitment to quality and expects the supplier to meet or exceed the standard of 100% conformance to GM processes, policies, and procedures.
Remarks. Support for dimensional engineering deliverables. The GM Dimensional Engineering team member assigned to this SOR is listed on the GM Buyer’s Contact list. The GM Dimensional Engineering team member will:
Assist supplier(s) in understanding and implementing GM’s Dimensional Engineering processes, policies, and procedures.
Review dimensional engineering deliverables as required and defined in Section 4.
Review the GM Dimensional Engineering Plan incorporated in the Geometric Dimensioning and Tolerancing drawings (GD and T).
Attend/participate in technical reviews conducted by Advance Purchasing to obligate the potential suppliers to the GMW15745 requirement.
