ISO 4759-3 Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F - Fourth Edition
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- ISO 2692 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) - Second Edition
- 01
- ISO 2692 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) - Second Edition
- 01.100
- BSI BS EN 14399-5 High-strength structural bolting assemblies for preloading Part 5: Plain washers
- CEN EN ISO 4759-3 Tolerances for Fasteners - Part 3: Plain Washers for Bolts, Screws and Nuts - Product Grades A and C
- BSI BS EN ISO 7093-2 Plain Washers - Large Series - Part 2: Product Grade C
- BSI BS EN ISO 4759-3 Tolerances for Fasteners - Part 3: Plain Washers for Bolts, Screws and Nuts - Product Grades A and C
- BSI BS EN ISO 7093-2 Plain Washers - Large Series - Part 2: Product Grade C
- CEN EN ISO 4759-3 Tolerances for Fasteners - Part 3: Plain Washers for Bolts, Screws and Nuts - Product Grades A and C
- CEN EN ISO 4759-3 Tolerances for Fasteners - Part 3: Plain Washers for Bolts, Screws and Nuts - Product Grades A and C
- BSI BS EN ISO 7093-2 Plain Washers - Large Series - Part 2: Product Grade C
- BSI BS EN ISO 4759-3 Tolerances for Fasteners - Part 3: Plain Washers for Bolts, Screws and Nuts - Product Grades A and C
- BSI BS EN ISO 7093-2 Plain Washers - Large Series - Part 2: Product Grade C
- BSI BS EN ISO 7093-2 Plain Washers - Large Series - Part 2: Product Grade C
- BSI BS EN ISO 4759-3 Tolerances for Fasteners - Part 3: Plain Washers for Bolts, Screws and Nuts - Product Grades A and C
- BSI BS EN ISO 4759-3 Tolerances for Fasteners - Part 3: Plain Washers for Bolts, Screws and Nuts - Product Grades A and C
- BSI BS EN 14831 Fasteners Tightening performance Torque/Angle simplified test method
- BSI BS EN ISO 15330 Fasteners - Preloading Test for the Detection of Hydrogen Embrittlement - Parallel Bearing Surface Method
- BSI BS EN 15048-1 Non-preloaded structural bolting assemblies - Part 1: General requirements
- CEN EN 14399-1 High-strength structural bolting assemblies for preloading - Part 1: General requirements
- Картотека зарубежных и международных стандартов
International Organization for Standardization
Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F - Fourth Edition
N 4759-3
Annotation
This part of ISO 4759 specifies tolerances for flat washers of product grades A, C and F with nominal diameters of 1 mm to 150 mm inclusive, designed to be used in bolted joints in combination with bolts, screws, studs and nuts.
This part of ISO 4759 may be applied to non-flat washers however it does not include all the tolerances related to these washers.
It applies to non-captive and captive washers, and to standard and non-standard washers.
It does not apply to dynamic disc springs.
Washers of product grades F and A are intended to be used with bolts, screws, studs and nuts of product grades A and B; washers of product grade C are intended to be used with bolts, screws, studs and nuts of product grade C.
NOTE The product grade refers to a specific tolerance range related to dimensional and geometrical characteristics (product grade F for fine tolerances, product grade A for precise tolerances, product grade C for large tolerances).
Annex A presents tolerances taken from ISO 286-1 and ISO 286-2.
Автоматический перевод:
Допуски для застежек - Часть 3: Шайбы для болтов, винтов и гаек - продукт градуируют A, C и F - Четвертый Выпуск
