ASTM B230/B230M Standard Specification for Aluminum 1350–H19 Wire for Electrical Purposes
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- ASTM B983 REV A Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube
- 23
- ASTM B983 REV A Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube
- 23.040
- ASTM B983 REV A Standard Specification for Precipitation Hardened or Cold Worked, Seamless Nickel Alloy Pipe and Tube
- 23.040.15
- ASTM E1268 Standard Practice for Assessing the Degree of Banding or Orientation of Microstructures
- ASTM E3 Standard Guide for Preparation of Metallographic Specimens
- ASTM B961 Standard Specification for Silver Coated Copper and Copper Alloy Stranded Conductors for Electronic Space Application
- ASTM E3 Standard Guide for Preparation of Metallographic Specimens
- ASTM E3 Standard Guide for Preparation of Metallographic Specimens
- ASTM B961 Standard Specification for Silver Coated Copper and Copper Alloy Stranded Conductors for Electronic Space Application
- ASTM B961 Standard Specification for Silver Coated Copper and Copper Alloy Stranded Conductors for Electronic Space Application
- ASTM B624 Standard Specification for High-Strength, High-Conductivity Copper-Alloy Wire for Electronic Application
- ASTM E8/E8M REV A Standard Test Methods for Tension Testing of Metallic Materials
- ASTM B706 Standard Specification for Seamless Copper Alloy (UNS No. C69100) Pipe and Tube
- ASTM B193 Standard Test Method for Resistivity of Electrical Conductor Materials
- ASTM B901 Standard Specification for Compressed Round Stranded Aluminum Conductors Using Single Input Wire Construction
- Картотека зарубежных и международных стандартов
ASTM International
Standard Specification for Aluminum 1350–H19 Wire for Electrical Purposes
N B230/B230M
Annotation
This specification covers aluminum 1350–H19 (extra hard) round wire for electrical purposes.
The values stated in inch-pound or SI units are to be regarded separately as standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard.
NOTE 1-Prior to 1975 aluminum 1350 was designated EC aluminum.
NOTE 2-The aluminum and temper designations conform to ANSI H35.1/H35.1M. Aluminum 1350 corresponds to UNS A91350 in accordance with Practice E527.
NOTE 3-For definitions of terms found in this specification relating to uninsulated electrical conductors see Terminology B354.
Автоматический перевод:
Стандартная спецификация для алюминиевого 1350–H19 провода в электрических целях
Эта спецификация покрывает 1350–H19 алюминий (дополнительный твердый) круглый провод в электрических целях.
Значения утвердили в дюйме-фунте, или единицы СИ должны рассматриваться отдельно как стандарт. Значения в каждой системе не являются точными эквивалентами; поэтому, каждая система должна использоваться независимо от другого. Объединение значений от этих двух систем может привести к несоответствию со спецификацией.
