CEI EN 60455-3-8 Resin based reactive compounds used for electrical insulation Part 3: Specifications for individual materials Sheet 8: Resins for cable accessories
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- CENELEC EN 60684-3-282 Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 282: Heat-shrinkable, polyolefin sleeving - Stress control
- 29
- CENELEC EN 60684-3-282 Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 282: Heat-shrinkable, polyolefin sleeving - Stress control
- 29.035
- CENELEC EN 60684-3-282 Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 282: Heat-shrinkable, polyolefin sleeving - Stress control
- 29.035.20
- BSI BS EN 1012-1 Compressors and vacuum pumps - Safety requirements Part 1: Air compressors
- BSI BS EN ISO 14122-3 + A1 Safety of machinery - Permanent means of access to machinery - Part 3: Stairways, stepladders and guard-rails - AMD: August 31, 2010
- BSI BS EN 1846-2 + A1 Firefighting and rescue service vehicles Part 2: Common requirements - Safety and performance - CORR: November 30, 2010; AMD: August 31, 2013
- BSI BS EN 60204-1 + A1 Safety of machinery. Electrical equipment of machines. Part 1: General requirements - AMD: April 30, 2009; CORR: May 31, 2010
- BSI BS EN 1846-2 + A1 Firefighting and rescue service vehicles Part 2: Common requirements - Safety and performance - CORR: November 30, 2010; AMD: August 31, 2013
- BSI BS EN ISO 14122-3 + A1 Safety of machinery - Permanent means of access to machinery - Part 3: Stairways, stepladders and guard-rails - AMD: August 31, 2010
- BSI BS EN ISO 14122-3 + A1 Safety of machinery - Permanent means of access to machinery - Part 3: Stairways, stepladders and guard-rails - AMD: August 31, 2010
- BSI BS EN 1846-2 + A1 Firefighting and rescue service vehicles Part 2: Common requirements - Safety and performance - CORR: November 30, 2010; AMD: August 31, 2013
- BSI BS EN 60204-1 + A1 Safety of machinery. Electrical equipment of machines. Part 1: General requirements - AMD: April 30, 2009; CORR: May 31, 2010
- BSI BS EN 1846-2 + A1 Firefighting and rescue service vehicles Part 2: Common requirements - Safety and performance - CORR: November 30, 2010; AMD: August 31, 2013
- BSI BS EN 1846-2 + A1 Firefighting and rescue service vehicles Part 2: Common requirements - Safety and performance - CORR: November 30, 2010; AMD: August 31, 2013
- BSI BS EN 60204-1 + A1 Safety of machinery. Electrical equipment of machines. Part 1: General requirements - AMD: April 30, 2009; CORR: May 31, 2010
- CENELEC EN 60684-3-285 Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 285: Heat-shrinkable polyolefin sleeving, for medium voltage joint insulation
- CENELEC HD 629.1 S2 Test requirements on accessories for use on power cables of rated voltage from 3,6/6(7,2) kV up to 20,8/36(42) kV Part 1: Cables with extruded insulation - Incorporates Amendment A1: 2008
- Картотека зарубежных и международных стандартов
Comitato Elettrotecnico Italiano
Resin based reactive compounds used for electrical insulation Part 3: Specifications for individual materials Sheet 8: Resins for cable accessories
N EN 60455-3-8
Annotation
This sheet 8 of IEC 60455-3 gives the requirements for resins for power cable accessories which conform to this specification and meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not on this specification alone.
Автоматический перевод:
Смола базировала реактивные составы, используемые для электрической Части 3 изоляции: Спецификации для отдельного Листа материалов 8: Смолы для кабельных аксессуаров
Этот лист 8 из IEC 60455-3 усадки требования для смол для аксессуаров силового кабеля, соответствующих этой спецификации и встречающих установленные уровни производительности. Однако выбор материала пользователем для определенного применения должен основываться на фактических требованиях, необходимых для соответствующей производительности в том применении а не на одной только этой спецификации.
