ISO 3019-2 CORR Hydraulic fluid power Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Part 2: Metric series Technical Corrigendum 1
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- ISO 3019-2 Hydraulic Fluid Power - Dimensions and Identification Code for Mounting Flanges and Shaft Ends of Displacement Pumps and Motors - Part 2: Metric Series - Third Edition; Cancels and Replaces ISO 3019-3:1988
- 23
- ISO 3019-2 Hydraulic Fluid Power - Dimensions and Identification Code for Mounting Flanges and Shaft Ends of Displacement Pumps and Motors - Part 2: Metric Series - Third Edition; Cancels and Replaces ISO 3019-3:1988
- 23.100
- ISO 3019-2 Hydraulic Fluid Power - Dimensions and Identification Code for Mounting Flanges and Shaft Ends of Displacement Pumps and Motors - Part 2: Metric Series - Third Edition; Cancels and Replaces ISO 3019-3:1988
- 23.100.10
- DIN 5480-2 Involute splines based on reference diameters - Part 2: Nominal and inspection dimensions
- DIN 5480-15 Berichtigung 1 Involute splines based on reference diameters - Part 15: Inspection
- DIN 5480-2 Involute splines based on reference diameters - Part 2: Nominal and inspection dimensions
- DIN 5480-15 Berichtigung 1 Involute splines based on reference diameters - Part 15: Inspection
- DIN 5480-15 Berichtigung 1 Involute splines based on reference diameters - Part 15: Inspection
- DIN 5480-2 Involute splines based on reference diameters - Part 2: Nominal and inspection dimensions
- DIN 5480-2 Involute splines based on reference diameters - Part 2: Nominal and inspection dimensions
- BSI BS ISO 3019-2 Hydraulic fluid power - Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors - Part 2: Metric series - CORR 16976: Febraury 28, 2007
- ISO 3912 Woodruff Keys and Keyways First Edition; (NZS/ISO 3912: 1977)
- ISO 3019-2 CORR Hydraulic fluid power Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Part 2: Metric series Technical Corrigendum 1
- DIN 5480-1 Involute splines based on reference diameters - Part 1: General
- Картотека зарубежных и международных стандартов
International Organization for Standardization
Hydraulic fluid power Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Part 2: Metric series Technical Corrigendum 1
N 3019-2 CORR
Annotation
This part of ISO 3019 establishes a metric series of mounting flanges and shaft ends for positive-displacement,rotary hydraulic fluid power pumps and motors. It specifies sizes and dimensions and establishes an identification code foe two- and four-bolt, and polygonal (including circular), mounting flanges, as well as for cylindrical keyed shafts ends, conical keyed ends with an external thread and metric involute spline shaft ends.
NOTE Involute spline is in accordance with DIN 5480.
Автоматический перевод:
Измерения питания гидравлической жидкости и идентификационный код для монтажных фланцев и концов вала Части 2 объемных насосов и двигателей: Метрический ряд Техническое Исправление 1
Эта часть ISO 3019 устанавливает метрическую серию монтажных фланцев и концов вала для положительного смещения, ротационных приводных насосов гидравлической жидкости и двигателей. Это определяет размеры и измерения и устанавливает противника идентификационного кода два - и с четырьмя болтами, и многоугольный (включая проспект), монтажные фланцы, а также для цилиндрических включенных концов валов, конических включенных концов с внешней резьбой и метрических запутанных концов вала шлица.
