CEN EN ISO 5349-1 Mechanical Vibration - Measurement and Assessment of Human Exposure to Hand-Transmitted Vibration - Part 1: General Requirements
Данный раздел/документ содержится в продуктах:
- Техэксперт: Машиностроительный комплекс
- Картотека зарубежных и международных стандартов
- SNV SN EN 894-4 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 4: Location and arrangement of displays and control actuators
- 13
- SNV SN EN 894-4 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 4: Location and arrangement of displays and control actuators
- 13.110
- 13.180
- BSI PD IEC/TS 62850 Safety requirements for electrical equipment for measurement, control, and laboratory use - General requirements for equipment intended to be used in educational establishments by children
- BSI BS EN 894-3 + A1 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators - AMD: June 30, 2009
- BSI BS EN 574 + A1 Safety of machinery - Two-hand control devices - Functional aspects - Principles for design - AMD: February 28, 2009
- BSI BS EN 894-3 + A1 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators - AMD: June 30, 2009
- BSI BS EN 894-3 + A1 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators - AMD: June 30, 2009
- BSI BS EN 574 + A1 Safety of machinery - Two-hand control devices - Functional aspects - Principles for design - AMD: February 28, 2009
- BSI BS EN 574 + A1 Safety of machinery - Two-hand control devices - Functional aspects - Principles for design - AMD: February 28, 2009
- BSI BS EN ISO 11111-1 Textile machinery - Safety requirements Part 1: Common requirements
- BSI BS EN 1005-4 + A1 Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery - AMD: June 30, 2009
- CEN EN ISO 14738 Safety of machinery - Anthropometric requirements for the design of workstations at machinery
- CEN CEN/TR 16391 Mechanical vibration and shock - Hand-transmitted vibration - Influence of coupling forces at the hand-machine interface on exposure evaluation
- Картотека зарубежных и международных стандартов
European Committee for Standardization
Mechanical Vibration - Measurement and Assessment of Human Exposure to Hand-Transmitted Vibration - Part 1: General Requirements
N EN ISO 5349-1
Annotation
This part of ISO 5349 specifies general requirements for measuring and reporting hand-transmitted vibration exposure in three orthogonal axes. It defines a frequency weighting and band-limiting filters to allow uniform comparison of measurements. The values obtained can be used to predict adverse effects of hand-transmitted vibration over the frequency range covered by the octave bands from 8 Hz to 1 000 Hz.
This part of ISO 5349 is applicable to periodic and to random or non-periodic vibration. Provisionally, this part of ISO 5349 is also applicable to repeated shock type excitation (impact).
NOTE 1 The time dependency for human response to repeated shocks is not fully known. Application of this part of ISO 5349 for such vibration is to be made with caution.
This part of ISO 5349 provides guidance for the evaluation of hand-transmitted vibration exposure, specified in terms of a frequency-weighted vibration acceleration and daily exposure time. It does not define limits of safe vibration exposure.
NOTE 2 Annex C is concerned with the approximate relative importance of various characteristics of the vibration exposure which are believed to produce health effects.
Автоматический перевод:
Механическая вибрация - измерение и оценка воздействия на человеческий организм переданной рукой вибрации - часть 1: общие требования
